Graymills Oil Seperator Osep-2 Series OMI Manuel d'utilisateur télécharger pdf (Page 1)

OSEP-2

Fluid Conditioning

System

Operation and

Maintenance

Instructions

Do not install or operate until you have read all

warnings and instructions and understand the

operation of this equipment.

• The OSEP-2 is not intended for and will not function

with solvent-based fluids. Using flammable or com-

bustible fluids will create a safety hazard.

• Read and follow all safety instructions supplied with

the coolant used in your machine tool or machining

center.

• Ensure that all fittings and connections are properly

tightened.

• Be sure that there are no bends or kinks in the fluid

return hose back to the tank. A blockage in the fluid

return line will cause the coalescing chamber to over-

flow.

Never work with equipment you feel may be

unsafe. Contact your Supervisor immediately.

INTRODUCTION

Upon receipt of the OSEP-2 immediately inspect the fil-

tration system for any damage that may have occurred

during shipping. The OSEP-2 is shipped completely

assembled and will only require minor adjustments and

connections to be completed for operation. The unit is

designed to continuously remove tramp oil and suspend-

ed solids.

SITE REQUIREMENTS

• The OSEP-2 requires a level area within ten feet of the

tank or sump it is servicing.

• The unit requires a space of approximately two feet (2')

by three feet (3'). This will allow access to the equip-

ment for service and inspection.

• Plant air with a maximum of 50 psi is also required to

operate unit. Position unit within reach of plant air.

• This equipment requires an air connection (maximum

pressure 50 psi) but does not require an independent

electrical power source.

• The system weighs approximately 170 pounds dry.

Once it is charged with aqueous coolant, it will weigh

approximately 300 pounds.

SET-UP AND INSTALLATION

• Remove OSEP-2 from skid by removing two of the

front wooden hold-downs.

For stationary installation, place next to machine tool

sump/tank and adjust threaded levelers accordingly.

795-90654

GM 04-01

1 2 3 4

Résumé du contenu

Page 1 - Instructions

OSEP-2Fluid ConditioningSystemOperation andMaintenanceInstructionsDo not install or operate until you have read allwarnings and instructions and under

Page 2 - OPERATION & MAINTENANCE

For portable installation, remove threaded levelers andreplace with heavy-duty dual wheel swivel casters(provided).• Connect the 3/8" clear sucti

Page 3 - REPLACEMENT CARTRIDGES

INSTALLATION DIAGRAMREPLACEMENT CARTRIDGES767-90700 Standard cartridge767-90706 Optional cartridge for fine particulate removal767-90707 Optional cart

Page 4 - WARRANTY

Graymills Corporation 3705 N. Lincoln Avenue Chicago, IL 60613-3594 (773) 248-6825 FAX (773) 477-8673 www.graymills.comWARRANTYGraymills Corpora

Commentaires sur ces manuels

Pas de commentaire

Graymills Oil Seperator Osep-2 Series OMI Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement pour l'eau Graymills Oil Seperator Osep-2 Series OMI. Graymills Oil Seperator Osep-2 Series OMI User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Graymills Oil Seperator Osep-2 Series OMI Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement pour l'eau Graymills Oil Seperator Osep-2 Series OMI. Graymills Oil Seperator Osep-2 Series OMI User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement pour l'eau Graymills Oil Seperator Osep-2 Series OMI